Movincool PC7 Manual de Serviço descarregar pdf (Página 27)

Operation Section

    &AN-ODE#ONTROL3WITCH

Ê ÊÊ Ê ÊÊÊ Ê UÊ /iÊ v>Ê ÌÀÊ «iÀ>ÌÊ ÃÊ VÌÀi`Ê LÞÊ Ài>ÞÃÊ Ê ÌiÊ Ài>ÞÊ L>À`Ê ÌÀÕ}Ê >Ê VÀ«ÀViÃÃÀÊ 

the control panel assembly. The fan program in the microprocessor can be changed by a DIP

switch on the left side of the relay board located in the control box.

Ê ÊÊ Ê ÊÊÊ Ê UÊ/iÀiÊ>ÀiÊÌÜÊÃiÌÌ}Ã\

(1) Cool to stop

Ê ÊÊ Ê ÊÊÊ Ê UÊ 7iÊ ÌiÊ *Ê ÃÜÌVÊ ÃÊ ÃiÌÊ Ê ÌiÊ `ÜÜ>À`Ê ÀÊ -/"*Ê «ÃÌ]Ê ÌiÊ VÀ«ÀViÃÃÀÊ VÌÀÃÊ Ìi

fan motor using the same room temperature thermistor that it uses to control the compressor. In

this case, both the fan and the compressor stop when the microprocessor receives a sufﬁciently

low intake air (room temperature) signal from the thermistor (equal to or less than the set point).

When the temperature increases (exceeds the set point) the microprocessor restarts the fan and

compressor automatically. However, if the unit has been off for less than 120 sec, the fan starts

before the compressor (time delay feature).

(2) Cool to operate

Ê ÊÊ Ê ÊÊÊ Ê UÊ7iÊ ÌiÊ *Ê ÃÜÌVÊ ÃÊ ÃiÌÊ ÌÊ ÌiÊ Õ«Ü>À`Ê ÀÊ "*,/Ê «ÃÌ]Ê ÌiÊ VÀ«ÀViÃÃÀÊ VÌÀÃ

the fan operation using control panel inputs only. The fan operates continuously during fan only

and cool modes. (This is the factory default setting.)

    4EMPERATURE3CALE$ISPLAY3WITCH

Ê ÊÊ Ê ÊÊÊ Ê UÊ7iÊ ÌiÊ *Ê ÃÜÌVÊ ÃÊ ÃiÌÊ Ê ÌiÊ `ÜÊ ÀÊ ºc»Ê «ÃÌ]Ê ÌiÊ ÃiÌÊ «ÌÊ >`Ê ÀÊ Ìi«iÀ>ÌÕÀiÊ >Ài

displayed in degrees Celsius. “°C” is indicated on the LCD. When the DIP switch is set in the up

or “°F” position, the set point and room temperature are displayed in degrees Fahrenheit . “°F”

is indicated on the LCD. (This is the factory default setting.)

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 61 62

Sem comentários

Movincool PC7 Manual de Serviço Página 27